How to apply installation templates

Once Templates have been created they can be applied.  By applying previously created Templates, Chai DSE and OXPd:Workflow components will be applied to the selected devices or groups.  It is important to note, when applying Templates, Templates must be applied in the following order: 1) Chai DSE, 2) OXPd:Workflow and finally 3) Authentication Agent (if authentication is used on the device).  It is important to note that each component must be successfully installed prior to installing the next component.  Also note, that uninstallation must occur in reverse starting with 1) Authentication Agent (if authentication is used on the device), 2) OXPd:Workflow and finally 3) Chai DSE.

How to apply the Chai DSE template

  1. To apply template solutions, click Apply.
    This opens the Apply Solution Template.
  2. Select the template to be used.
  3. Under Selection method, click Devices or Groups. If you select Devices, all available devices will be returned, and you should complete the following steps:
    1. Use Source to select a specific group of devices.
    2. After you select the devices, click the >> button to add devices to the Selected devices panel.
      Groups which consist of more than one device can be selected as well.  Instructions for creating Groups can be found at the beginning of this document.
    3. Click Next.
  4. Click Apply Template to install the solution.
    Important: When the template is applied, the device will automatically reboot.
    A status screen will be displayed which shows whether the installation was successful.
  5. To verify that the Chai DSE files are installed, use the following link:
    • http://{Device_IP_Address}/hp/device/hp.OXPdSolutionInstaller

    The following message should be displayed:

    Chai Digital Send Enablers - V 4.3.0
    Load Status: Loaded
    Applying the OXPd:Workflow Template                  
                      

Applying the OXPd:Workflow Template

  1. To apply template solutions, click Apply.
    The Apply Solution Template will be displayed.
  2. Select the template to be used.
  3. Under Selection method, click Devices or Groups. If you select Devices, all available devices will be returned, and you should complete the following steps:
    1. Use Source to select a specific group of devices.
    2. After you select the devices, click the >> button to add devices to the Selected devices panel.
      Groups which consist of more than one device can be selected as well.  Instructions for creating Groups can be found at the beginning of this document.
    3. Click Next.
  4. Click Apply Template to install the solution.
    Important: It is important to note when the template is applied, the device will automatically reboot.
    A status screen will be displayed which shows whether the installation was successful.
  5. To verify that the OXPD:Workflow jar files are installed, use the following link:
    • http://{Device_IP_Address}/hp/device/hp.OXPdSolutionInstaller
    The following message should be displayed:
    OXPd:Workflow 1.4.9.0 
    Load Status: Loaded
    Applying the Authentication Agent Template
                   

Applying the Authentication Agent Template

  1. To apply template solutions, click Apply.
    This displays the Apply Solution Template.
  2. Select the template to be used.
  3. Under Selection method, click Devices or Groups. If you select Devices, all available devices will be returned, and you should complete the following steps:
    1. Use Source to select a specific group of devices.
    2. After selecting the devices, click the >> button to add devices to the Selected devices panel.
      Note: Groups which consist of more than one device can be selected as well.  Instructions for creating Groups can be found at the beginning of this document.
    3. Click Next.
  4. Click Apply Template to install the Authentication Agent.
    A status screen will be displayed which shows whether the installation was successful.
  5. To verify, enter the URL, http://device_ip/hp/device/this.loader where device_ip is the IP address for the device into a web browser.
  6. In the Reloadable Packages section, see if “AutoStore Auth Agent” is listed.